Whole-House Repiping for Central Florida Homes

Every plumbing system has a lifespan. When yours reaches the end of it, the signs tend to cluster: a pinhole leak in the guest bath, then another in the kitchen wall six months later, rusty water first thing in the morning, showers that never seem to have enough pressure. At that stage, chasing individual leaks costs more than solving the problem. K&K Plumbing’s whole-house repiping service replaces aging supply lines with modern piping, planned around your household so the disruption is as small as possible.

Identify the pipe you have

Look under sinks, at the water heater, and where the main line enters the house. Here is what you might find:

• Gray or blue flexible plastic, often stamped PB. This is polybutylene, widely installed in Florida homes from the late 1970s through the mid-1990s. It can become brittle from reaction with disinfectants in municipal water and tends to fail without warning, often at fittings.
• Dull gray threaded metal. Galvanized steel rusts from the inside, narrowing the pipe and discoloring water. It is mostly found in older homes.
• Copper with green spots or repeated pinholes. Copper itself is durable, but in some water conditions it thins over time. Multiple pinholes are a sign the whole run is wearing out.
• White or cream rigid plastic (CPVC). Generally fine, though older CPVC can become brittle, especially in hot attics.

Our article on evaluating older pipe materials includes photos and more detail.

Choosing new piping

Material	Strengths	Considerations
PEX	Flexible, fewer fittings, resists scale and freeze splitting, quieter	Must be protected from direct sunlight
Copper	Long track record, rigid, heat tolerant	Higher material cost, more fittings, can be affected by aggressive water
CPVC	Lower cost, corrosion resistant	More brittle with age and heat, more joints

PEX is our most common recommendation for repiping because it can be snaked through walls and attics with fewer access points. The benefits of PEX are worth reading if you’re comparing options, but we’ll go through the decision with you in person.

How a repipe project runs

Assessment and quote

We inspect your current piping, note the fixture count and layout, test water pressure, and look at where lines run. You receive a written quote that spells out material, scope, and what’s included.

Preparation

Furniture near work areas is moved or covered, floors are protected, and we confirm permit requirements for your jurisdiction.

New lines in, old lines out of service

New supply lines are run through walls, ceilings, and the attic. Lines under the slab are typically abandoned in place rather than dug out, which also eliminates future slab leak risk on those runs. Each fixture gets a new shutoff valve.

Switchover and testing

Fixtures are connected to the new system, the old piping is disconnected, and the entire system is pressure tested. Inspections are scheduled where required.

Openings closed

Access openings are kept as small as practical. We will be clear upfront about drywall patching and how it is handled for your project.

Florida factors that push repiping

Slab construction means many original lines run under concrete, and a home that has already had one slab leak is likely to see more if the pipe is the same age. Hot attics are hard on older plastic lines. Hard water and disinfectant chemistry contribute to both polybutylene failures and copper pinholes. And because so many Central Florida neighborhoods were built in the same few decades, whole streets of homes tend to reach the repipe stage around the same time. We see this regularly in The Villages and older neighborhoods around Brooksville.

Cost factors

We don’t quote repipes over the phone because the price depends on the home. The biggest factors are the number of bathrooms and fixtures, single- versus two-story layout, attic access, the material you choose, how much finished surface needs to be opened, and permit fees. You get a firm, upfront number after we’ve seen the house.

Ready to stop chasing leaks?

If your home has had more than one leak in recent years, or you’ve found polybutylene under the sink, it’s worth getting a professional opinion. Call or text 352-810-9472 to schedule a repiping assessment with K&K Plumbing.